- #Stm32x device protected download zip#
- #Stm32x device protected install#
- #Stm32x device protected archive#
- #Stm32x device protected code#
Warning: you are about to flash firmware which is older than the firmware on the device (v0.4.11-dev).ĭo you want to flash this firmware anyway? y I also tried using the command “odrivetool dfu path/to/firmware/file.hex” but that gave me the following error: ODrive control utility v0.4.11įound ODrive 2075387E304E (v3.6-56V) with firmware v0.4.11-dev
I then put our Odrive (v3.6) in DFU mode by flipping the DIP switch, and tried flash it over USB with the command “sudo dfu-util -a 0 -s 0x08000000 -D path/to/bin/file”, but it gave me the error message: dfu-util: Invalid DFU suffix signatureĭfu-util: A valid DFU suffix will be required in a future dfu-util release!!!ĭetermining device status: state = dfuERROR, status = 11ĭetermining device status: state = dfuIDLE, status = 0ĭownloading to address = 0x08000000, size = 174460ĭownload 0% 0 bytesdfu-util: ERASE_PAGE not correctly executed However, when I tried to reflash it with our ST-link I got an error message “STm device protected”. I managed to flash the firmware successfully, and have confirmed that it works by looking at the CAN messages being sent. ℹ️About GitHub Wiki SEE, a search engine enabler for GitHub WikisĪs GitHub blocks most GitHub Wikis from search engines.I modified the CAN firmware (razoredge branch) so that error, axis state, current, and position is continuously streamed in the heartbeat message (since the position in our application we are using won’t be larger than the int16 max and min values). Under “Read Out Protection” pull-down menu, change the protection level from 1 to 0 and then apply the changes.ĭisconnect from STM32 Link Utility and head on over to VSC to upload the firmware. In the main toolbar select “Target->Option Bytes”.
If wired correctly, upon connection a warning prompt will state that the MCU cannot be read to due protection write. Once connected, open STM-Link Utility, click on “Target->Connect” (or the grey plug icon). Pictures here or in VSC (Explorer tree, >src, >target, >r81, mcu_side.jpg). Once downloaded and installed, connect the ST-link to the R81 receiver according to the wiring To unlock the MCU begin by downloading STM32-Link Utility (you may need to sign-up with an email address to do so). "Programming StartedError: stm32x device protectedĮmbedded:startup.tcl:521: Error: Programming Failed " If an unlocking error is encountered head to “Unlocking” step. If all connections are correct, upload should take a matter of seconds. Returning to the VSC toolbar at the bottom of the screen, click on the arrow (Upload). In VSC (Explorer tree, >src, >target, >r81, mcu_side.jpg). VSC will now build the firmware.Īfter a few moments, with the build being complete, if you haven't already done so, wire up the R81 receiver to the ST-link according to or On the VSC screen, the bottom toolbar of VSC will contain various icons. Return to VSC, click” File->Open folder” and navigate to the folder where the Redpine firmware was previously saved.Įnsure that the folder containing the platformio.ini file is selected.
#Stm32x device protected archive#
Unzip the archive in the location that you wish.
#Stm32x device protected download zip#
Navigate to, download zip of source code.
#Stm32x device protected install#
Once installed, open VSC and under extensions search for "PlatformIO IDE" and install package.
#Stm32x device protected code#
Stm32-Link Utility *Depending on the receiver and whether it is lockedīegin by downloading and installing Visual Studio Code (VSC).
0 kommentar(er)
